Propeller Props, 10PCS 6040 6×4 Remote Control propellers for Remote Control Aircraft Quadcopter Remote Control Aircraft 2450Special for Motor skrnrhrery

Good price for quality
These looked to be average plastic propellers. Nothing was wrong with them, or the quality, but unfortunately they were a lot larger than what I needed them for. They are the size of an IPhone 15 roughly.

break easy
not for beginners breaks tooooeasy

Functional – But Be Sure To Balance Your Props
6×4 propsPaired these with a 2205 2300KV motor running 4SSome Pros and ConsPROS-All Props rotate the same direction so no mixing of CW and CCW (good for planes)-Flexible (better for preventing broken propellers)CONS-Flexible (this might not be the best options for high speed wings-Not balancedOVERALLThese props are a good value for most implementations. If you plan on going extra fast and have an expensive plane, these probably are not for you. If you want good value and god durability, then these are a good choice.Headlight and tailight LED kitThis led 8 piece headlight and taillight kit is marketed for RC trucks, but I’m using them in a RC plane. I assume these are 5 volts (which is a safe bet, but the listing doesn’t say what voltage input is required)Some Pros and ConsPROS-No fuss wiring, just find 5 volts and your have lights (-Taillights are spot on-8 Leds-bezels look realCONS-Headlights are really on bright when you are looking directly at them, it helps if you have the bezels onOVERALLThis worked fine for my RC plane. I don’t need them to see where I’m going, I need them to better see where the plane is and these lights fit that purpose. If you are using an RC car and expect them to light your path in complete darkness, these are not that.30 piece control hornsThese are the u clips / clevis I have been searching for, these a made out of a very strong nylon that allows the screws to not strip out the threads when connecting to the control rodsPROS-Controls have 4 holes which gives you more options for throws-U clips are really strongCONSCan’t think of anyOVERALLThe U Clips are exactly what I want in terms of ability to grab onto the control rod/linkage. You can see in the video that I am putting some much pressure on the control rod that goes through the foamboard and the control rod bends but the U clip does not slide.POOL FLOATWow this river float is really made out of heavy duty material (it’s .45mm PVC, which is rather thick). The dual tube style float is not something you see very often.Some Pros and ConsPROS-heavy duty as far as causal floats go ( the float weighs just a little over 10lbs)-drink holder-strings so you can connect multiple floats together.-Storage box (that’s great for snacks and other items)-660 lb weight capacityCONSNone that I can think ofOVERALLThis works awesome in our pool. I think it would do well in a lazy river. I do not think this is good for tubing or rapids. It’s heavy duty, but I don’t think it will take a lot to rip out the mesh bottom, so I don’t suggest letting people jump into the float. It’s a good size float, so for most people it should be fairly stable and easier to get into than some of those smaller ones. The backrest is a nice touch, but my favorite thing is the storage box/snack holderI already had one of these hex wrenches that came with a quad, but I really needed two of them so I could tighten lock nuts on the same bolt that holds folding propellers on a prop spinner.It is made out of a solid metal, it weighs about 10 grams.PROS-Worked as described-All Metal ConstructionCONS- None that I could think ofOVERALLThis met my needs by all accounts. Having two of these makes adding and removing folding props so much easier than using one and trying to use pliers on the other nut.Picked this tri color Red, Blue Yellow silk PLA because it had YELLOW in it. Most of the other tri-color PLA’s tend to use “gold” which comes out either orange or very light.One of the most important features for me when it comes to filament is does the filament get kinked or gets stuck on the spool. I had no issues with this filament doing this.Some Pros and Cons-Yellow as a part of tri-color PLA gives off a much different color pattern than the more commonly found gold-No bed or layer adhesion problems-Tangle Free spoolCONS-The only con is, I don’t care for the cardboard spool holders.OVERALLThis worked just fine on my Ender 3 V3 KE printer. I printed the standard speed Benchy as the test print (the 16 min one), so the settings for that test print are a lot higher than what is recommended for this PLA, and the results came out fine.Note, check out the color separation in the photos, you can really see the three different colors on the spool.Mini ProjectorScriptThis is the Mini portable projector by ULTIMEAHas 5g/2.4g WifiBluetoothBrightness is 300 lumensElectric FocusCompaitable with Android, Windows, IOS1 HDMI port and 2 USB portsIncludes HDMI________________Unboxing was pretty straight foward______________I was looking for a small projector to watch TV/movies in the backyard using my phone and also do tracing of images onto large sheets of foam board. This mini projector seemed to have about the right dimension and specs for what I needed.Some Pros and Cons:PROS-Ability to adjust the focus with the remote-Keystone feature works well-Dual wifi 5G and 2.4g-Decent brightness-Multiple connection options-Has nut for attaching the projector to a tripod-HDMI option worked well-Windows media player works over wifi-Comes with HDMI cable-Has built in speakerCONS-Menu is not initiative-Never could get bluetooth to work-”Casting” means screen mirror from your phone-Does not support casting tabs from your browser-Image is not the sharpestOVERALLThis is not going to replace your big screen TV in terms of sharpness and brightness. This mini project should be fine for situations where highest quality video is not required, think outdoor family get together or kids sleep over. My biggest issue is that you can “cast” directly from your phone like you can with Chromecast, you can only use screen mirroring. When I ordered this, the ability to cast directly from my phone was the main reason I wanted this, I never got that option to work to my satisfaction. Instead, I ended up hooking a laptop to it, not ideal.BUG ZapperFirst off, the flame is very realistic at night, especially if there is no ambient light around or if the Bug Zapper is not too close to a solid object like a wall or fence. There is no assembly required at all, the only thing you need to do is unbox it from the cardboard box then take it out of the box it came in and untwist the wire holding the power cable.It was a lot bigger than I was expecting, which is good, it is about 18 inches tall and maybe 12 inches wide at the top. The top appears to be metal and the hook is metal. The first time I plugged in outside, I was near the house and I didn’t hear any bugs get zapped. The 2nd time I plugged it in, it was in the garden and it fried something big right away.Some Pros and CONS-Zaps Bugs-Heavy duty frame-Realistic flame-Dusk to Dawn feature-Safe-Big-Zero assemblyCONS-Only con I could think of is I don’t think there’s an on/off switchOVERALLI was pleasantly surprised at how realistic the flame was and how big the unit is. It does zap bugs, what I don’t know is does the style of light (i.e. the fake flame repel some bugs). The flame is so realistic, I would not surprise me if the company offers non-bug zapper type lights like candles.2s 900 30 Lipo2S and 900 mah is a flexible combination. Because these two batteries have traditional balance plugs, you can charge them with 2S chargers or on a balance charger. They are small enough to put RC Radios, in small 2s planes, or combine 2 of them into a 4S config using an adapter which is what I’m doing. I put these in a very small delta wing plane. Although you can put this on a quad/drone, the 30C might be a problem if you are doing racing, long distance should be fine.PROS-900mah is hard capacity to come buy in 2S-has multiple connection options-cells were well balanced and arrived at proper storage voltage-quality wire leadsCONS-for my application, I’d rather that an xt30 connectorOVERALLThese have enough power for low to medium draw RC needs (no EDF jets). I’ve only used them a couple of times, so I don’t know how durable the battery is or how well it holds up to repeated charging cycles.PLA Dual Color PLA Filament, Sky Blue and Pink PLA Filament,This is a dual collar pink and sky blue silk PLA filament by OVV3D.. What I like about these multicolor filament spools is that each brand of filament has a slightly different pattern even if they are the same two colors, which gives you a lot of different options. My review is based on using the Ender 3 V3 KE, and my test print was the “16 Minute Speed Benchy” that comes with the unit, since that is a good frame of reference for a lot of people. I will also that the speed settings for the Speed Bench are much higher than the recommended settings for the silk PLA (meaning the quality would likely be even better if I followed the recommended speed settings)Some PROS and CONS.PROS-Tangle Free, this is always the 1st thing I test because it does not depend on the printer being used-Prints at high speed-Color pattern is unique-Good bed adhesion on PEI sheet-Good layer adhesionCONS-Couldn’t think of anythingOVERALLI like using silk multi color filament for trinkets and anything where you want to add some flare to your prints. I don’t really use them for functional prints. You can get a lot better quality out of this filament if you slow down the print speed to the recommended settings and reduce your layer height. Major selling point for me is this does not tangle.PINK 4×4 TruckThis Pink 4×4 Monster Truck by BLUEJAY Store is fun indoors and outdoors as toy grade RC. I was impressed at how durable the truck is as well as the quality of the remote control. I have a couple of other RC vehicles that are toy grade and by far the remote control for this 4×4 is a lot better. It has lot of power, there are two speeds, I’d recommend slow speed for indoors unless you are on carpet because the tires will spin and the vehicle will whip around and be a little hard to control.Some PROS and CONSPROS:-Durable-Comes with two batteries for the truck-Comes with the charger-Comes with LED lights underneath-Comes with headlights-Works reality well indoors-Works well outdoors on pavement (no so much the grass)-Easy to put together-Comes with some spare partsCONS-No AA batteries for the remote are included-Not really big enough to work in grass.OVERALLI love this thing, my dog loves it even more. I got about 25 mins out of each battery hard driving I’m guessing. The bumper does are really good job of taking hits off walls and furniture. This is a toy grade, yet I found it do much better than the avg toy grade. I think a 7 year old could drive it with a little practice.Billing Air PumpGot this solar air pump to use in my outdoor hydroponics bucket for tomatoes.This unit is marketed for ponds, bird baths, and hydroponics, it comes with two air stones and has a battery backup to help it run through the overnight hours. Easy to build and easy to install. Some Pros and ConsPROS-2 airstones are included-generous amount of silicone air tubing included-has battery backup-easy to assemble and install-3 modes-Solar panel seems to be well matched in size to the unitCONS-No indication of how much air it pushes per hour-Not sure the batteries and be replaced if they wear outOVERALLThis should be fine for bird baths and small hydroponic installations. This is clearly better than not having an air pump, but don’t expect you are going to see massive bubbles come up in a pond that is ½ the size of one’s house.OVONIC 4 Packs 650mah 3S1P 11.1V 80C Lipo Battery Pack with XT30 Plug for RC AirplaneThese 3s 650mah batteries are the sweet sport for mini quads and a small sail planes or DIY gliders. I have 2.5” quad that takes up to 3S but can’t handle the heavier versions. Also have a DIY foamboard glider that has the 2212 3s 1400KV motor and these batteries are perfect for that. The 80C rating is good enough for most quads, and gives you even more head room for planes. These have very little voltage sag on the quad and almost doesn’t exist on the plane.Some Pros and ConsPROS-3S 650 is perfect for DIY foamboard planes using those affordable 2212 motors out there-Silicone wires-XT30 instead of XT60-Arrived at storage voltage of 11.4 for all for piecesCONS-None that I could think of.OVERALLThese batteries fill a niche in that they are 650 and not 850, which means they will fit in smaller builds. I’m using them on a light weight foamboard plane that I built from scratch. These are marketed towards “airplanes” but with 80C you can put them in quads as well.NOTE: The image in the listing says 850mah (as of 5/15/2024), but listing says 650mah and 650 is what arrives.Drill BitsI got these to use on aluminum to create motor mounts for my RC plane. Had no issue going through that metal. I haven’t tried any really tough metals to see how they hold up, nor am I planning on using them for any really tough metals.So far I have only used on of the 10 that come in the pack and it is holding up wellThese worked great for my purposes, your mileage may vary.PROS-Work well on aluminum-Seem to wear wellCONS-I don’t see the case lasting very long.OVERALLI can’t speak to how well these drill bits wear over time or how they work on harder metals for if you force them using a drill press, but for me and my needs, this is all I need.3S LiPo Battery with Charger Kit, 2200mAh 11.1V 35C Lipo Battery with Deans T Connector for RC Airplane RC Quadcopter Helicopter Drone FPV, with 2S-3S Battery Balancer ChargerI don’t have any airplanes or vehicles that take a Dean’s connector, but I do have an adapter for xt60 to Deans, so not really an issue for me. I have a lot of batteries but only have two chargers, mainly fly 3s and 4s, but most of my radios runs on 2s. Always seems like when I need to charge a radio battery, the chargers are taken up with 3s and 4s batteries. The charger alone was a motivating factor for me in getting this battery/charger combo. The charger comes with the option to charge 2s and 3s batteries (NOTE YOU CANNOT Charge both types at the same time).The battery is 35C which is good for most planes (except EDF Jets), some quads, and most vehicles.PROS-charger does 2s and 3s-Charger easy to use-charger has lights for each cell so you can see how much charge the battery has-the battery is 35C, which although not what you want for a 5 inch racing quad, should be perfect for most airplanes and vehicles-battery arrived at storage voltageCONS-3 x 800mah charging is not blazing fastOVERALLThe charger alone makes this combo worthwhile. I can’t speak to how well the battery holds to multiple charges. I don’t plan on using it in planes with more than a 20amp max draw so, I don’t expect it to get overly stressed given the 35C rating. This is also perfect for someone getting into the RC hobby that doesn’t have a good grasp of lipos, cells, mah, and volts because this charger just works, it takes most of the guesswork out of charging. So good beginner battery charger or backup battery charger for more experienced RC hobbyists.Wood Filing CabinetThis arrived in way more pieces than I was expecting and took a long time to assemble in part because the instructions are just pictures and the pictures are not very detailed so it was difficult to determine the direction and orientationMost of the pieces were marked with numbers and or letters for identificationI finally got it put together, but one of the drawers didn’t sit square or flush to the outer cabinet.OVONIC 130C 4S 850mah Lipo Battery 14.8V Pack with XT60 Plug for FPV Racing 4S 850mah lipos are often harder to find than 650mah, 1300mah, and 1500mah. I’m using these in a small delta style wing, 130C is more than plenty for my needs. 130C is a great option for quads as well. 130C gives you plenty of head room when giving quads punch out. I don’t really have any quads geared for 850mah 4s, but have quads that use bigger batteries, like 1500mah and the 130C makes all of the difference in terms of voltage sag. With that said, I did try this in my 6 inch quad, and there was hardly any voltage sag. Once the throttle was lowered, the OVONIC battery voltage jumped right back up.Some Pros and ConsPROS-130c-delivers the power-quality silicone wires for battery leads and balance leads-arrived at storage voltage (each cell was about 3.8Vs across all 4 batteries)-XT60CONS-Only real con for some, but not for me, the XT60 instead of XT30. 850 is kinda of the dividing line a lot of times for XT30 and XT60.OVERALLI think these batteries fill a sweet spot between the more common 4S 650 and 4S 1300 batteries out there. THe 850’s are small enough to fit in smaller builds but give you a little more flight time. Regarding the XT60 instead of the XT30, I feel like OVONIC made the right choice given these are 130C, 130C is for high amp draw, having the larger connectors helps keep voltage sag to a minimumI’ve been using 12KG servos in my RC FAN boat to turn the prop and the rudder, but sometimes it wasn’t enough. These 30KG…….so much torque.This is my 1st set of 30kg servos so I don’t have any other ones to compare it to.Some Pros and ConsPROS-plenty of torque-truly metal geared-comes with the basic attachmentsCONS-Couldn’t really think of anyOVERALLThese should work where high torque is a requirement for your servo. Note, these are quite heavy, so don’t plan on using them in a plane, unless it is a really large one.2G METAL GEAR SERVOI put these in my small DIY foamboard power glider. I’m just using two servos, one for elevator and one for both ailerons.Plastic gear servos probably would have been fine, but these 2G metal gear servos deliver alot of confidence. I have crashed several times trying to find the CG on my plane and so far these have held up very well to the abuse.PRO-All metal gear-responsiveCONS-the plugs, I needed regular futba style servo connectorsOVERALLThese worked on m glider very, I just had to modify the plugs for my needs.Creality K1 AI Camera 1080P HD Camera Compatible with K1 and K1 Max 3D Printers – Real-time Monitoring on Your Phone and Enhanced EfficiencyI ordered the wrong camera. I thought this was USB and could be used with the Ender 3 V3 KE. This does not work with the Ender 3 V3 KE or any other 3d printers that require a USB connection.The camera is a lot smaller than I was expecting, not that it should affect the quality of video. Note there are no cables that come with this camera, apparently the K1 already has the cable on the motherboard.Recommendation, listing should clearly state this is not the USB version8AH Dewalt Battery RepalcementThis these 8AH 20V Lithium Ion batteries by orstaimer fit my Dewalt 20V Cordless Drill (DCD771) and replaced battery (DCB207)PROs-Fits the DCB207 battery as advertise-No voltage sag-Arrived at the proper storage voltage-Has indicator light for how much charge the battery has left while using the toolCONS-The only con is, I’m not sure at this point I trust the stated 8ah rating based on the weight of the battery. The standard 1.3ah battery (DCB207) weighs about 300 grams. This battery claims to have almost 5 times the storage capacity of the standard battery, but only weighs about 600 grams.OVERALLThe main takeaway is that these batteries fit my drill. Time will tell if they hold to their charge well and if they hold up to multiple charges, but for now I’m giving them 5 stars.